JIN LI YUAN
Precautions for the installation of plastic water tanks
Release time:
2024-05-28 09:28
1、 Installation environment: When installing a plastic water tank, it should be in a horizontal position and able to withstand the weight when the tank is filled with water; Due to the protrusion of the bottom of the water tank towards the box during production, an appropriate amount of fine sand can be used to fill the bottom during installation, increasing the load-bearing capacity of the bottom of the water tank; The temperature around the water tank cannot exceed the limit range of cold and heat resistance of the water tank.
2、 Test sealing: Before the plastic water tank is officially put into use, it should be filled with water to test for leakage to prevent unnecessary losses. If storing chemical raw materials, there should be drainage ditches and dilution devices around the plastic water tank.
3、 Selection of hole interface accessories: The opening and accessories are configured according to the specific use of the customer, including PE flanges PVC、ABS、 Stainless steel, iron interfaces, etc. are available for selection; Strong acid and strong alkali, the organic solvent inlet and outlet are connected by PE material flanges, such as containing 98% concentrated sulfuric acid, less than 65% concentrated nitric acid, organic solutions (formaldehyde, toluene, etc.). We can provide corresponding reference solutions when purchasing water tanks from our company.
4、 Joint and flange installation: When installing a plastic water tank, the joint or flange connected to the bottom of the tank should be perpendicular to the barrel wall, making it easy to use soft connections or shock absorbers. Water tanks with a capacity of more than 10 tons need to be equipped with reinforcement sleeves to avoid uneven force on the barrel wall after being filled with liquid, which may damage the outlet connection and cause leakage. In severe cases, it may even damage the joint and barrel body. When unloading and installing, please use a crane and professional installation personnel to command.
5、 Installation of scaffolding: If it is necessary for workers or mechanical equipment to work on the top of the water tank during work, a scaffolding or ladder should be installed next to the water tank to ensure safe operation; When the liquid level cannot be controlled, install an overflow port to prevent liquid from overflowing from the inlet, affecting personal safety, and regularly check the safety of the water tank and its pipelines.
Recommended news
Transparent plastic blow molding processing tips
In mold planning, attention should be paid to the following issues (including product planning) in order to avoid poor plastic molding caused by poor activity or uneven cooling, resulting in appearance defects and transformation. Generally, in mold planning, the following points should be noted:
The manufacturing process of transparent plastics
（1） The preparation and dryness of materials can affect the clarity of goods due to the presence of any impurities in plastic, thus affecting storage and transportation. During the feeding process, it is necessary to pay attention to sealing to ensure the cleanliness of the material. Especially when the material contains moisture, heating can cause the material to transform, so it must be dry, and it is necessary to use a dry hopper when adding materials during injection molding. It should also be noted that during the dry process, the input air should be filtered and dehumidified to ensure that it does not contaminate the material. The drying technology of Tongming Plastics: Data \ Technology Drying temperature (℃) Drying time (h) Material layer thickness (mm) Whitening PMMA70-802-430-40pc120-130>6<30 Choose hot air circulation drying PET140-1803-4 Choose continuous drying feeding equipment is preferred.
The blow molding process of transparent plastics
Due to its high light transmittance, Tongming plastic must have strict requirements for the appearance quality of plastic products, without any spots, pores, or whitening. Mist halo, black spots, discoloration, and poor gloss are the drawbacks that affect the quality of materials and equipment throughout the entire blow molding process.
Blow molding, also known as hollow blow molding, is a rapidly developing plastic processing method. The tubular plastic preform obtained by extrusion or injection molding of thermoplastic resin is placed in a split mold while it is hot (or heated to a softened state). After the mold is closed, compressed air is immediately introduced into the preform to blow and expand the plastic preform tightly against the inner wall of the mold. After cooling and demolding, various hollow products are obtained.
The production steps of plastic water tanks
Explanation of the steps for making plastic water tanks: Plastic water tanks are processed using synthetic material polyethylene (HDPE), and the commonly used methods for making plastic water tanks can be roughly divided into two categories: Type 1: Rotational molding production method, one-time molding
The bearing range of plastic water tanks and storage tanks
The advantages of water tanks (storage tanks, water towers) are well-known: wide temperature range, non-toxic, odorless, anti extension, anti penetration, impact resistance, and corrosion resistance. Therefore, they are widely used in industries such as food, daily use, chemical, household, agriculture, machinery, and medicine. However, even the best water tank has its load-bearing range, which we must pay attention to.
Online Message
Tel: +86 13736609339 / +86 152 6720 6288
Mail: jinliyuanplastic@163.com
#417 Jing‘an town, Xinqian st. , Huangyan, Taizhou, Zhejiang